Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Aaron_adams

Pages: [1] 2 3
1
Laser Parts / Re: Needing rollers for a3 frame
« on: April 22, 2018, 09:45:53 AM »
Anyone else ?

2
Laser Parts / Re: Needing rollers for a3 frame
« on: April 18, 2018, 07:54:07 PM »
Roughly what my wheel is
OD: 22
ID: 4.75
Thick: 10

3
Laser Parts / Re: Needing rollers for a3 frame
« on: April 15, 2018, 07:14:51 PM »


http://i682.photobucket.com/albums/vv190/aaron_t_adams/IMG_20180415_153520_zps7a7tyyd3.jpg

4
Laser Parts / Needing rollers for a3 frame
« on: April 14, 2018, 01:09:16 PM »
Where can I get the rollers for the a3 frame ?

5
T2 Engraving / Re: Trying a few images
« on: September 11, 2017, 06:05:32 PM »
Got it now I need to slow it down some it's not burning to good in the wood I'm using

6
T2 Engraving / Re: Trying a few images
« on: September 11, 2017, 05:22:00 PM »
I still can't get my image to look like that, I need some help

7
T2 Engraving / Re: Trying a few images
« on: September 10, 2017, 06:19:43 PM »
The size is 127 mm and mine still shows solid and not like yours ?

8
T2 Engraving / Re: Trying a few images
« on: September 10, 2017, 05:07:24 PM »
Will I burn up my last letting it run at 200 minutes

9
T2 Engraving / Re: Trying a few images
« on: September 10, 2017, 02:18:29 PM »
https://www.google.com/search?q=tulia+hornet&client=ms-android-verizon&prmd=inv&source=lnms&tbm=isch&sa=X&ved=0ahUKEwjq2PK1xZvWAhVB7iYKHbVqDMUQ_AUIESgB&biw=412&bih=604&dpr=2.63#imgrc=gaZhCT-XIij8EM:

10
T2 Engraving / Re: Trying a few images
« on: September 10, 2017, 02:10:46 PM »
Feed rate is 1000 feed rate vector is 500 and rapid feed rate is 2000

11
T2 Engraving / Re: Trying a few images
« on: September 10, 2017, 02:00:43 PM »
Doing the black and white and what speed should I run ?

12
T2 Engraving / Trying a few images
« on: September 10, 2017, 01:51:12 PM »
Im trying to do a few mascot images on a 8x8 piece of wood and it's saying it's going to take 250 minutes to do a 5x5 inch image, is there any tips or tricks around this

13
Projects / Re: Trying to get a project done
« on: June 23, 2017, 06:39:45 PM »
Ok I put a image in t2 how do I get it to start the engraving at 0,0 ?

14
Projects / Re: Trying to get a project done
« on: June 20, 2017, 06:00:08 PM »
Where do I get the driver ?

15
Projects / Re: Trying to get a project done
« on: June 19, 2017, 04:46:01 AM »
I can't get communication

Pages: [1] 2 3