Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Camera

Pages: [1] 2
2
General Discussion / Nejelaser
« on: May 10, 2020, 04:17:19 AM »
Anybody use NEJELaser mini engraver?

3
General Discussion / Driver problem again
« on: April 26, 2020, 11:57:50 PM »
After three years got the driver problem, it comes back now.

The error is: This device is not working properly because Windows cannot load the drivers required for this device. (Code 31).

Object Name already exists.

I have tried physically deleted WCH.CN directory and files.  Reinstalled it by using T2Laser update driver.  Still can't solve the problem.

By the way, it is a different computer.  I am using registered T2Laser on my desktop.  I am now trying my very old laptop using trial version of T2Laser.  If works, I consider to buy another license and move the engraver and laptop permanently to the shed.

4
EleksMaker Mana SE / Focus Laser
« on: April 20, 2020, 10:21:32 PM »
The old board got a button WEAK LASER which I could turn the laser on for focusing.  Now there is no such a button for the new board. How do I turn on "WEAK" laser for focus in T2?

I have tried to put 5 Laser Power in T2 and start trace frame laser on.  It still burns.

5
EleksMaker Mana SE / 2 Wire Laser
« on: April 20, 2020, 04:08:04 AM »
I just received my new EleksMaker Mana SE v3.2 board.  The board's laser has 3 wires for PWM control but my old cheap laser only got 2 wires (on and off).  How should I connect it to the board?  Please help.

6
T2 Engraving / 20W Laser Engraver
« on: February 26, 2020, 03:19:18 AM »
Can T2 Laser support this machine?  There is one controlled by mobile phone too.

https://www.gearbest.com/laser-engraving-machine/pp_009955161231.html

7
T2 Engraving / My engraver got trouble
« on: February 25, 2020, 02:14:40 AM »
Having been asking questions here for quite a long time.

My machine was working fine until I did something stupid.  I unplugged the x-axis and plug in a stand alone motor to play with T2 Laser's rotary function.  Of course it didn't work.  I plugged back to the original settings.  All of sudden, all motors didn't work (not moving at all).  After messing around in T2 Laser, it worked again and I forgot what I have done.  Now the laser was always on (of course, I have switched off it on the board) and in full power.  Well I will try to play again tomorrow.  I am tired now.  If anybody knows how to solve this problem, please let me know.  It will save me a lot of time.

Thanks.

8
T2 Engraving / Not Working
« on: June 24, 2018, 12:38:03 AM »
Exactly the same problem from last year happens again (http://benboxlaser.us/index.php/topic,2405.msg28404.html#msg28404)

Windows 10 64bit automatically doing update in the past few days. My engraver won't work now.

This time I thought I had experience and tried to solve it by deleting the Windows 10 USB driver and it installed automatically for me again without any problem.  It is USB Seria Port (COM3) when I plugged in the engraver.  It said it is working properly.  This port will disappear when I unplug the engraver. I tried reinstall CH341SER driver manually or through T2 Laser.  I have tried using different USB cables. It just don't recognise the port in T2 Laser.  It is empty in T2 Laser.  No port is detected in T2 Laser.  Any suggestion how to fix it?

9
T2 Engraving / DXF part disappear
« on: April 02, 2018, 06:37:39 PM »
I tried to laser cut a simple thing (please see attached dxf file and jpg files).  For some reason some part was missing.  Sometimes even the whole right hand part was missing.  What have I done wrong?

10
T2 Engraving / Windows won't recognise driver
« on: August 06, 2017, 04:40:08 AM »
Worked for several months and for unknown reason it didn't work today.  Windows 10 couldn't recognise the driver CH341SER.  I tried to install it and it all went well successful and under device manager still said unknown device.  Using Windows device Manager to install the driver and it said it couldn't.  Tried to use different USB ports, reboot the machine, still no use.  What's wrong?  Please help.

11
STL / Extended Foot
« on: June 28, 2017, 12:20:39 AM »
I read a topic created by micky that he wanted to raise the frame.  It is quite simple to do it in Fusion 360.  So I have made a few version to replace the original one (if broken), or raise 30mm or 50mm to give more room to move around.

https://www.thingiverse.com/thing:2408210

12
T2 Engraving / DXF Import
« on: June 20, 2017, 12:54:30 AM »
I try to import a very simple dxf file into T2 Laser and it didn't come up correctly.  It is just a letter "a".  I used other software to read the dxf file, it was okay with an "a" but in T2 Laser it just shows the hole in the "a".  Anything I did wrong?

13
STL / Air Blower
« on: May 01, 2017, 05:00:03 PM »

14
Projects / Air blower
« on: April 24, 2017, 08:30:05 PM »
I have made a flexible and expandable air blower for my benbox laser.  Thinking of vacuum but without a filter it is pointless.  I have tried it and it works fine.

15
Banggood.com / Help please
« on: February 15, 2017, 12:14:21 AM »
I have big problem with Banggood recently.  Can anybody advise me how to get my money back?  I used Paypal and I lodged a dispute already.  I tried very hard to solve the problems with Banggood.  Unfortunately they tried to ignore my messages.  The product they shipped to me was 100% faulty and even the manufacturer admitted it.

Pages: [1] 2