1
T2 Engraving / Command to swap bits?
« on: October 07, 2020, 02:53:40 AM »
Hello, I am sure I have seen the command to change the tool inside T2laser, but I can't remember how to use it. Thanks.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
T2 Engraving / Menu inactive after sending gcode
« on: May 05, 2020, 09:50:04 AM »
I have a weird issue - after my gcode has been sent and the ending command is M30. T2Laser menu becomes inactive - it keeps saying 'Sending' and the only button I can press is Emergency stop. Is this normal?
3
T2 Engraving / Bluetooth connection
« on: September 16, 2019, 10:18:00 AM »
I am going to connect Bluetooth HC-05 module to control my CNC, not laser. I need to configure the module via AT commands first to set up parity bits, even, uneven as well as stopbits. Do you have any idea which values should I choose for that? Should I be looking for grbl defaults?
4
T2 Engraving / PCB engraving from SVG
« on: September 01, 2019, 04:46:01 AM »
Hello Zax.
I would be very grateful if you could explain how can I engrave this file using T2 laser. Since there is no support of SVG, I assume it needs to be converted. I tried using inkscape, but I beleive there are some settings that I am missing.
Thanks a lot in advance.
I would be very grateful if you could explain how can I engrave this file using T2 laser. Since there is no support of SVG, I assume it needs to be converted. I tried using inkscape, but I beleive there are some settings that I am missing.
Thanks a lot in advance.
5
T2 Engraving / Turning T2 laser into CNC software
« on: October 27, 2018, 01:32:03 PM »
Hello Zax.
Thank you for what you are doing. I am enjoying using T2 laser for my laser cutter. But I have recently purchased small CNC machine and have several questions:
Do you have plans to add more features that will be usefull for CNC owners?
I also have a couple of other questions:
- In settings it's possible to select Z axis mode - laser focus or CNC. When I select CNC mode, settings are not saved when I quit T2 laser (focus mode is selected by default. Is it possible to fix it? Why it's possible to select both modes simaltaneously? Shouldn't it be just one mode selected at a time?
- Is it possible to improve resetting home position within a single button push? Correct me if I am wrong, but now you can't reset Z axis position.
- Maximum spindle speed can be set to 1000 only, whereas gbrl 1.1 allows to set RPM, so the value can be greater than 1000. Is it possible to fix it?
- Laser mode is enabled by default and needs to be changed each time control window is opened. Can it be fixed?
Thank you for what you are doing. I am enjoying using T2 laser for my laser cutter. But I have recently purchased small CNC machine and have several questions:
Do you have plans to add more features that will be usefull for CNC owners?
I also have a couple of other questions:
- In settings it's possible to select Z axis mode - laser focus or CNC. When I select CNC mode, settings are not saved when I quit T2 laser (focus mode is selected by default. Is it possible to fix it? Why it's possible to select both modes simaltaneously? Shouldn't it be just one mode selected at a time?
- Is it possible to improve resetting home position within a single button push? Correct me if I am wrong, but now you can't reset Z axis position.
- Maximum spindle speed can be set to 1000 only, whereas gbrl 1.1 allows to set RPM, so the value can be greater than 1000. Is it possible to fix it?
- Laser mode is enabled by default and needs to be changed each time control window is opened. Can it be fixed?
Pages: [1]