Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - ItzzTommy

Pages: [1]
1
General Discussion / Inverting the picture.
« on: December 06, 2018, 11:54:25 AM »
I got this picture, i just wanna invert the colors on the middle of it, not everything, is that a possibility in t2laser?

2
Ive tried changing ports, but it wont work, im stuck, could someone tell me what to do?

3
General Discussion / The ends doesn't meet.
« on: November 12, 2018, 07:35:07 AM »
Ive found another problem.

Im using T2Laser, and this problem comes on every thing im engraving, i need some advice!

- Tommy

4
General Discussion / Auto trace.
« on: October 21, 2018, 01:24:07 AM »
When i auto trace. I do the "Trace Image"

But do i have to click everything i want to engrave, or is there a faster way?

- Tommy

5
General Discussion / Burning double
« on: October 17, 2018, 09:22:06 AM »
If i load in a picture, it burns double, help!

- Tommy

6
General Discussion / Distance from laser head to working object
« on: October 10, 2018, 01:40:27 PM »
How far is the "ideal" distance from the laser head to the object ur burning on, my other laser has 4 cm over the object.

On the current one that's 1x1m i have the object 14 cm under, is that to far, my laser is 2500W.

- Tommy

7
General Discussion / Feed rate meanings..?
« on: October 10, 2018, 11:42:53 AM »
So i got the t2laser.

Feed Rate engraving was deafult 2000. That was too fast.
Feed Rate 950 was too low, but 1000 was fine.

Feed Rate (Vector) is linked with feed rate engraving, does that making any difference?

And what does Rapid Feed Rate have to do with this?

- Tommy

8
General Discussion / Problems with x-motor
« on: October 09, 2018, 03:16:43 AM »
I bought t2laser, and i tried it now, found a problem that quick.

Y-motors is just going one way, i do "generate gcode" and come in to where i can control the laser, when i make it go down, it goes down, when i make it go up, it goes down.
But if i change the y1 with the place y2 was in, and y2 to where y1 was.
Then they only go up, and when i click down then, it still goes up.

And the X-motor doesn't wanna work.

- Tommy

9
T2 Engraving / T2Laser payment.
« on: October 06, 2018, 11:46:37 AM »
I saw something, but cant remember, wasnt it members got 20% off t2laser?
Can someone link me wher i pay member thing off t2laser?
Or gimme @Zax 's pp information so i can transfer over?

Regards
Tommy

10
General Discussion / I need some help.
« on: October 04, 2018, 09:25:20 AM »
Didn't get aliexpress link, but copy this to find it.
"2.5W laser, large 100*100cm,2500MW big DIY laser engraving machine,diy marking machine ,diy laser engrave machine,advanced toys"

I use benbox, all the motors work fine.
But the problem is.

When i burn something, in wood, there comes this line, where when it's not supossed to burn, and move from one space to another, it still is burning.
I will try to attach a picture later with it.

Ther is also another problem, the laser is on full all the time, even when it's at the zero point, not supossed to do anything.

Thanks for all the help yall can give me!

Regards
Tommy.

Pages: [1]