Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - ItzzTommy

Pages: [1] 2
1
General Discussion / Inverting the picture.
« on: December 06, 2018, 11:54:25 AM »
I got this picture, i just wanna invert the colors on the middle of it, not everything, is that a possibility in t2laser?

2
Ive tried changing ports, but it wont work, im stuck, could someone tell me what to do?

3
General Discussion / Re: The ends doesn't meet.
« on: November 12, 2018, 11:16:23 AM »
Do you think it's a backlash problem, i tried engraving a reindeer just now, took me 100 minutes, and it looks at a point, it just decides to move some centimeters up and engrave out of the plate.

Also the lines are very big, something that they shouldnt be.

Im attaching two files, original picture and the engraved picture

- Tommy

4
General Discussion / The ends doesn't meet.
« on: November 12, 2018, 07:35:07 AM »
Ive found another problem.

Im using T2Laser, and this problem comes on every thing im engraving, i need some advice!

- Tommy

5
General Discussion / Re: Auto trace.
« on: October 21, 2018, 09:30:42 AM »
I need auto trace so the engraving follows the line, but i don't want double lines.

Heeelp..?

- Tommy

6
General Discussion / Auto trace.
« on: October 21, 2018, 01:24:07 AM »
When i auto trace. I do the "Trace Image"

But do i have to click everything i want to engrave, or is there a faster way?

- Tommy

7
General Discussion / Re: Burning double
« on: October 20, 2018, 10:31:22 AM »
Okay, you have a point with the lost stepts, but the car is not double lined.
It's single lined.

Im droppin another pic with "double lines" that i just engraved, which is single lined in the picture.

- Tommy

8
General Discussion / Re: Burning double
« on: October 20, 2018, 10:14:17 AM »
But it's only with pictures.
If i only burn letters it wont burn double.

- Tommy

9
General Discussion / Re: Burning double
« on: October 20, 2018, 04:23:10 AM »
Hey again zax, i see this!

- Tommy

10
General Discussion / Re: Burning double
« on: October 19, 2018, 07:57:58 AM »
Ive tried for some hours for 2 days now, enabling and disabling options, but it wont work.
Here's a pic of bi-diagonal but it's not engraving, its scanning.

- Tommy
:o

11
General Discussion / Burning double
« on: October 17, 2018, 09:22:06 AM »
If i load in a picture, it burns double, help!

- Tommy

12
General Discussion / Distance from laser head to working object
« on: October 10, 2018, 01:40:27 PM »
How far is the "ideal" distance from the laser head to the object ur burning on, my other laser has 4 cm over the object.

On the current one that's 1x1m i have the object 14 cm under, is that to far, my laser is 2500W.

- Tommy

13
General Discussion / Re: Feed rate meanings..?
« on: October 10, 2018, 12:14:34 PM »
Thanks zax!

14
General Discussion / Feed rate meanings..?
« on: October 10, 2018, 11:42:53 AM »
So i got the t2laser.

Feed Rate engraving was deafult 2000. That was too fast.
Feed Rate 950 was too low, but 1000 was fine.

Feed Rate (Vector) is linked with feed rate engraving, does that making any difference?

And what does Rapid Feed Rate have to do with this?

- Tommy

15
General Discussion / Re: Problems with x-motor
« on: October 09, 2018, 03:21:31 AM »
I could not find any hex file, i have not flashed it.
There was no hex file, is that the problem, i use benbox hex file now, and benbox drivers.

- Tommy

Pages: [1] 2