Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - ThothLoki

Pages: [1] 2 3 ... 141
1
General Discussion / Re: Where is everyone? Did I miss something?
« on: November 06, 2018, 06:47:51 PM »
There still are some new people asking questions.
EleksMaker now has a Discord channel and I have been helping some new people there. I point them here and keep pushing T2 and BCL.

most want free and then complain that they dont work (for some reason).
It doesnt help that the EleksCAM dev left EleksMaker and kept the source code. EleksMakerZ is rebuilding the program from scratch and trying to improve it.

2
Trouble Shooting / Re: Firmware for this model
« on: October 29, 2018, 05:13:34 AM »
Can you look under the Nano (the little board with the usb) and let us know if there is a jumper under it?

3
BenCutLaser / Re: Upgrade Installation woes
« on: October 24, 2018, 07:41:14 PM »
My guess is that 3.2 has some dependencies that are 64 bit only or it was compiles for 64 bit only

4
Projects / Re: JTICE - My Engravings
« on: October 23, 2018, 06:24:26 AM »
I LOVE THAT BATHROOM SIGN!!!

5
General Discussion / Re: $2000 Budget - help me choose a CO2 Laser.
« on: October 22, 2018, 03:50:05 PM »
jtice,

have you given Lightburn a try? i hear it is a lot better than RD works.
Just what i have heard. i do not have any experience with either

6
T2 Engraving / Re: Linux support?
« on: October 22, 2018, 02:32:26 PM »
Thanks Zax.

Now i am making playonlinux guide too.

is more easy and you have icon on desktop.

anakein.
Did you ever make that playonlinux guide?

7
Cutting / Re: Help with settings for cutting
« on: October 18, 2018, 03:55:06 PM »
you need air assist and you need to raise your material up so there is an air gap underneath

8
General Discussion / Re: Fun with Boards
« on: October 16, 2018, 08:48:04 PM »
so tried with avrdude on a Raspberry pi (using 5v).
I may have gotten something wrong, but it cannot connect to the ship. i think this board is borked

9
General Discussion / Re: Circuit Building help (Challenge)
« on: October 16, 2018, 11:39:38 AM »
So I tinkered some more and came up with this solution ? It seems to work
RF can turn ON and OFF independently (when on the manual switch does nothing)
When RF is OFF the manual switch has two brightness levels using the resistors

Any shorts or danger with this circuit ?

Thanks for your help and suggestions Zax !!

Just and atheistic thing for me, but i would would set the supply voltage GND to the COM post on the toggle switch (middle one) and have the other two with the resistors go to the LEDs.

10
General Discussion / Re: Fun with Boards
« on: October 16, 2018, 11:37:01 AM »
it sends for a bit then fails.

I think i am doing something wrong, but will be playing more with it tonight. some of the pins are not broken out on the board  with easy access, so i end up needing three hands.

I should probably actually purchase an AVR programmer at some point. Do you have any thoughts on the USBasp?

11
General Discussion / Re: Fun with Boards
« on: October 16, 2018, 10:57:55 AM »
Tried that. Keep getting failed upload

12
General Discussion / Re: Quick and Cheap Laser Cover
« on: October 16, 2018, 10:56:48 AM »
I have a foam board enclosure as well. I like yours better

13
General Discussion / Re: Fun with Boards
« on: October 14, 2018, 07:07:15 PM »
yea, after some googling. i came to the same conclusion. it would work if i were uploading a sketch.

So if i dump the arduino bootloader into this board and it works, i should be able to dump a hex back in and go back to normal right?

14
General Discussion / Re: Fun with Boards
« on: October 14, 2018, 06:43:27 PM »
if i have an UNO as ISP, couldnt i just go from TX/RX on the UNO to RX/TX on the controller and burn the arduino bootloader?

15
General Discussion / Re: Fun with Boards
« on: October 14, 2018, 06:37:31 PM »
yea, Z just replied to me. D13 is not broken out. I will have to hold a jumper pin to it

Pages: [1] 2 3 ... 141