Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - ThothLoki

Pages: 1 2 3 [4] 5 6 ... 134
47
Benbox / Re: Problem benbox please help
« on: April 20, 2018, 10:37:59 PM »
As Zax said, Id you have jumper, go to 0.9 and never look back. I tried lost of software and am not a T2 fanboy. Benbox will never be installed again.

That said, if you NEED the Benbox firmware, talk to me. Just be careful about installing it agin. Most current downloads have malware attached

48
General Discussion / Re: Hello Everyone
« on: April 20, 2018, 09:59:55 PM »
Looking good! Now create some designs we can steal.  ;D

49
General Discussion / Re: Where do I start ?
« on: April 19, 2018, 03:51:16 PM »
We will be waiting......and watching.....and stealing your ideas.......

50
General Discussion / Re: Printing vases
« on: April 19, 2018, 03:50:12 PM »
I have not tried since installing my 0.7 nozzle... I will give it a go and report back, once I fix the printer!
But would nozzle size really have an effect on the quality of vase mode? I cant see how if you change the settings accordingly.
=)

Thicker wall maybe

51
Projects / Re: Autumn is here... Engraved curly wisteria seedpods
« on: April 17, 2018, 10:20:29 PM »
Yeah, you and Nottingham will become good friend......at making most of us look like rank armatures  ;)

He does have a good list, especially one of those rotary axis machines  ;)

I need o get back to finishing my air assist/focus ring that I started

This place is great for 3d questions as well. Everyone here helped my when I got my printer

52
General Discussion / Re: Printing vases
« on: April 17, 2018, 08:18:13 PM »
it could. i do overextrude when doing vase mode

53
General Discussion / Re: Spring is Coming!!!!
« on: April 17, 2018, 07:19:08 PM »
Ok. Spring is scheduled for next week. Should be in the 60s
Since last post, we got about another two feet of snow!! 

Anyways, I had to get the machine moving!

54
General Discussion / Re: Printing vases
« on: April 16, 2018, 08:29:16 AM »
Yeah. I made that mistake  a lot. I was going way too fast for case mode.

55
General Discussion / Re: Where do I start ?
« on: April 13, 2018, 09:59:34 AM »
Just get the printer. Most come with the basic software you need to get going. After that, you can start looking at different or better software

Between this forum, Thingiverse and YouTube, most of the questions I have had have been solved

56
General Discussion / Re: Printing vases
« on: April 12, 2018, 12:20:09 PM »
how do you up the wall thickness in vase mode? It is one perimeter thick.

57
General Discussion / Re: Where do I start ?
« on: April 12, 2018, 12:18:07 PM »
You need 3 "programs"
1. part designer
This could be openscad, blender, fusion 360, tinkercad, solidworks etc. This is where you build your 3d file (STL)

2. Slicer
This could be Slic3r, Cura and others. View this as the printer "driver" it converts your work (ie model) into a gcode file

3. G-Code Sender
Appls like Cura have the ability to slice the model and send the model to the printer. There are a few out there. I personally have a $10 Rasperry Pi Zero W running Octoprint connected to my printer. I then access it through a local web interface and can view/control my printer from any computer (i have 8 running at the moment), any phone (2 of them) or any tablet (lost count). The software is free and very robust.

Hope this helps

58
General Discussion / Re: honeycomb bed
« on: April 12, 2018, 12:12:24 PM »
confirmed doesnt work as well. there is a lot more flex than there should be. bitter voice of experience

59
General Discussion / Re: Where do I start ?
« on: April 11, 2018, 01:07:46 PM »
I have had a look around and absorbed quite a bit of information. It looks like I really need to get my hands dirty. I have spied a 3d printer printer on Amazon,   
Geeetech Acrylic Prusa I3 Pro B Unassembled 3D printer DIY...
GEEETECH
 
RRP: 310.00
Price: 169.00
You Save: 141.00(45%)
Dispatched from and sold by GIANTARM-EU.
At less than 170 it is cheap and should give me some good experience. Has anyone any experiences with this make/model ??

I believe Admin has one similar but from FolgerTech

if you are looking for easy, take a look at the MonoPrice Maker Select or the Anycubic i3

60
T2 Engraving / Re: beginning to get the hang of this
« on: April 10, 2018, 01:18:43 PM »
It's a natural progression. 2.5W laser etcher => 3d printer  => 40W CO2 cutter => CNC mill => divorce court.

Will get the mill before the CO2 but maybe not before the divorce court. The printer is almost taking care of that. I need to print more stuff for her

Pages: 1 2 3 [4] 5 6 ... 134