1
General Discussion / Re: 3D printer
« on: June 01, 2020, 10:37:19 AM »
i use fusion 360, 3dbuilder (for very stupid things) meshmixer and cura
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
4
EleksMaker Mana SE / Re: offline sd controller
« on: April 27, 2020, 12:53:00 PM »
perfect, I create special wiring and I try.
thank you very much Zax.
thank you very much Zax.
5
EleksMaker Mana SE / Re: offline sd controller
« on: April 27, 2020, 11:20:55 AM »
Hello guys,
I may have made a mistake
as I wrote above I took a manase and an offline controller but the wiring is different
my offline controller
looking online I see the pin names (see images)
the laser controller has gnd, 5V, rxd, txd, nc, rst
the manase has gnd, 5V, rxd, txd and others but not nc and rst
can i adapt it or do i have to buy cronos board?
CRONOS BOARD
I may have made a mistake
as I wrote above I took a manase and an offline controller but the wiring is different
my offline controller
looking online I see the pin names (see images)
the laser controller has gnd, 5V, rxd, txd, nc, rst
the manase has gnd, 5V, rxd, txd and others but not nc and rst
can i adapt it or do i have to buy cronos board?
CRONOS BOARD
6
General Discussion / Re: Odd Behavior
« on: April 26, 2020, 04:02:23 AM »
now we are strangely close 
7
MegaPi / Re: limit endstop megapi with grbl
« on: March 30, 2020, 01:03:08 PM »
parameter $ 21 is set to 1?
8
Trouble Shooting / Re: GRBL disappeared - can't reload
« on: March 28, 2020, 02:12:17 PM »
without internet how is it updated?
9
Benbox / Re: Pictures not in center
« on: March 17, 2020, 11:19:05 AM »No, I don’t use the same size. Here’s another one. Wish Benbox can ‘trace’ the picture itself with low light instead of ‘square’ so i can see where it’ll engrave
create another all black image and trace it
10
T2 Engraving / Re: Weird Double Engraving
« on: February 28, 2020, 06:36:40 AM »
the thickness probably hides the error
11
Trouble Shooting / Re: crazy new laser and crazy me
« on: February 27, 2020, 08:36:27 AM » laser is 2,5W ttl
I burned the images at f3500
i tried to cut at f100 s255
12
Trouble Shooting / Re: crazy new laser and crazy me
« on: February 26, 2020, 09:02:17 AM »
thanks for the reply
first it burned on non-stained wood (s1 / 255 f3500), after the cutting test it burns on stained wood (s70 / 140 f3500).
there is a lot of setup difference and the effect on the wood as well, from very light before to very dark after.
and before good image only on non stained wood and after only on stained wood.
the focus is ok.
my fear is that about 2 hours at maximum power have damaged the laser module.
I use birch laserply panels
I have successfully cut a 10mm square, the test with a5 design has failed, but this is not really a big problem, I use the laser to burn.
first it burned on non-stained wood (s1 / 255 f3500), after the cutting test it burns on stained wood (s70 / 140 f3500).
there is a lot of setup difference and the effect on the wood as well, from very light before to very dark after.
and before good image only on non stained wood and after only on stained wood.
the focus is ok.
my fear is that about 2 hours at maximum power have damaged the laser module.
I use birch laserply panels
I have successfully cut a 10mm square, the test with a5 design has failed, but this is not really a big problem, I use the laser to burn.
13
Trouble Shooting / crazy new laser and crazy me
« on: February 25, 2020, 12:24:53 PM »
Hello guys
I was trying the new TTL laser and the first 2 days I was able to make beautiful images on non-stained wood while on stained wood it had a golden effect.
on the third day I tried for 2 hours to cut 3mm of birch, without success.
after this (the images circled in blue) the laser was no longer able to burn on unstained wood while it became capable of burning stained wood.
because???
https://photos.app.goo.gl/1iPk5oY2Xtu399L47
I was trying the new TTL laser and the first 2 days I was able to make beautiful images on non-stained wood while on stained wood it had a golden effect.
on the third day I tried for 2 hours to cut 3mm of birch, without success.
after this (the images circled in blue) the laser was no longer able to burn on unstained wood while it became capable of burning stained wood.
because???
https://photos.app.goo.gl/1iPk5oY2Xtu399L47
14
T2 Engraving / Re: My engraver got trouble
« on: February 25, 2020, 12:17:01 PM »
you can do the reset of t2laser
