Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Moonie

Pages: [1] 2 3
1
Laser Accessories / Re: Replacing the Nano board with a 32bit board
« on: June 15, 2020, 06:32:16 AM »
And now im totally lost....

2
Laser Accessories / Re: Replacing the Nano board with a 32bit board
« on: June 15, 2020, 04:55:34 AM »
Hi Zax,

Ok now i'm totally confused ? Posting the screenshot from FB or is this not the truth ? According to these guys it will give you a much better greyscale range due to the 32 bit processor ?

regards

Moonie

3
Laser Accessories / Replacing the Nano board with a 32bit board
« on: June 15, 2020, 02:28:15 AM »
I have seen that most of the people using the Eleksmaker has replaced the Nano board with a 32bit board.

Will this board work :

https://www.robotics.org.za/NANO3C-FT232RL?search=nan

Sorry i know very little about this ! Does the above board have a boatloader and is it 32bit ?

Regards

Moonie

4
Hi,

Sitting with the same problem. I had a look at the eleksmaker site but cannot seem to find it ?! Maybe a link Zax ?

regards

Moonie

5
T2 Software Updates / Re: changing from windows 10x32 to 10x64
« on: April 03, 2018, 10:38:46 PM »
Thz Zak will do !

Moonie

6
T2 Software Updates / Re: changing from windows 10x32 to 10x64
« on: April 02, 2018, 10:35:40 PM »
Hi,

I was also looking into replacing the 500gb HD on my Dell with a SSD. What is the procedure for the licence of T2 ? Can i deregister it and do the swop, reinstall ?

regards

Moonie

7
Laser Accessories / Adding limit switches on the new Mana SE laser
« on: February 14, 2018, 09:56:02 PM »
Hi all,

On my old laser with the D7 board i had to do some soldering to add limit switches. Just received my new 2500W laser with the new Mana Se board (Blue laser). How do i add the limit switches ? Is there a plug on the board or do i have to solder again ?

regards

Moonie

8
3D Printer Software / Re: 3D Printer Slicers
« on: January 02, 2018, 09:32:35 PM »
Have a Tevo Tornado and been using Simplify3D since day one and it works like a rocket. I know there is a new program called ideamaker or something that the people are also raving about that is free. Simplify is very expensive at about $150 or something but worth it for me

9
Projects / Re: Portraits
« on: November 01, 2017, 10:29:32 PM »
Very very nice sir !

10
Custom Size Frames / Re: OpenBuilds ACRO Laser System
« on: October 13, 2017, 11:22:18 PM »
If i "transplant" my current laser and controller board to this system which is bigger will the T2 software still work on it ? Say if i built it 500x500mm ? I ordered a new A3 laser pro system from banggood since the price difference between a full system and just the 2500mw laser and a Mana SE controller borad was about $20. So i have a spare to play around with ;-)

regards

Moonie

11
General Discussion / Re: Talk me out of getting an Eleksdraw
« on: October 05, 2017, 06:50:51 AM »
I'm very happy with mine. Took me a couple of hours to assemble. Tested it, tried to do some mods and gave up. Now it is sitting on the shelf looking at me and i just leave it alone. As i said. very happy !

12
Projects / Re: Papercut shadowbox
« on: September 11, 2017, 04:38:41 AM »
You sir ! Are very talented !

13
General Questions / Re: No more than 30 min use WHY?!
« on: September 08, 2017, 04:14:40 AM »
Is there a option if you send a long job to the cutter that it will cut for say about 10 min and then switch of for a minute and the continue again ? If not would it be possible to incorporate this into the software maybe ? Or is there some other way of doing it (babysit with a stopwatch ?  ;D)

14
Projects / Re: Laser Engraver Improvements
« on: August 30, 2017, 03:01:28 AM »
Thx mate ! I have ordered a Wanhao i3 Mini which should arrive before the end of the month so then i can use that to print the parts.

15
Projects / Re: Laser Engraver Improvements
« on: August 28, 2017, 10:18:17 PM »
Hi,

If the chain cable is big enough so that you can pull the wire through without cutting the white connecter head off can you please send me a link to the files ?

Running a A3 laser

Pages: [1] 2 3