Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - John Henriksen

Pages: 1 [2] 3 4 5
16
General Discussion / Re: Stepper motor Nema 23 connecting
« on: March 04, 2018, 01:22:47 AM »
Okay I did found out by my selv surfing the net  :)

Now it is running smoothly both as x-axe or y-axe

By messuring the resistent on the wires I found the A and B pairs for the coils



17
General Discussion / Stepper motor Nema 23 connecting
« on: March 03, 2018, 10:50:29 AM »
Hi

I have this eleksmana board 3 axe

https://www.banggood.com/3-Axis-Stepper-Motor-Driver-Board-Controller-Laser-board-For-DIY-Laser-Engraver-p-1015947.html?rmmds=myorder&cur_warehouse=CN

and a Nema 23 stepper motor in this rotary tool

https://www.banggood.com/CNC-Router-Rotational-Rotary-Axis-CNC-Machine-Accessory-Tailstock-for-4th-Axis-p-1154485.html?rmmds=myorder&cur_warehouse=CN

It comes without a connector so just to be sure

The stepper motor have 4 wires but I am not 100% how to solder the wires to the connector 4-pin
Red, yellow, blue, green

What is the correct connection (i could guess that is is the same as my Eleksmana steppers)

I think that this datasheet for the Nema 23 is the correct one saying that it draws 2.5A and the board can draw 2A
Is it a problem drawing this Nema 23 motor?

https://motion.schneider-electric.com/downloads/quickreference/NEMA23.pdf

Great if you can  :)


18
Projects / Re: Wine Glasses
« on: February 27, 2018, 04:21:23 AM »
Hi

Have someone experimenting using a milling tool in a rotary setup for engraving glass?

When I get my rotary tool from china I will try it out  :)


19
Laser Accessories / Re: Adding limit switches on the new Mana SE laser
« on: February 15, 2018, 10:48:36 AM »
hi zax, thanks

I am not that good when we at talking elektronik wirering

so just wire the limit switch to d9 + ground and d10 + ground?

now lets say that x hits the limit switch then x will reverse some mm?
 

20
Laser Accessories / Re: Adding limit switches on the new Mana SE laser
« on: February 15, 2018, 05:19:58 AM »
I have just order limit switches , is there a good diagram for the connection?

I have a EleksMana 3 axes board and I don't need the home funktionality, just limit controls for x and Y

21
General Discussion / Re: Z axis
« on: February 13, 2018, 06:37:40 AM »
I applied 2 drops of oil into the gear, and now it works smoothly  :)

22
EleksMaker IV Axis / Re: Connecting 2 and 3 axes boards
« on: February 08, 2018, 12:34:06 AM »
Sorry

my mistake I have 2 and 3 axes bords (I forgot that there is 2 y-axes)  ;D

my 3 axes bord is this one
https://www.banggood.com/3-Axis-Stepper-Motor-Driver-Board-Controller-Laser-board-For-DIY-Laser-Engraver-p-1015947.html?rmmds=myorder&cur_warehouse=CN

23
EleksMaker IV Axis / Re: Connecting 3 and 4 axes boards
« on: February 07, 2018, 10:15:43 AM »
Hi Zax

Well I’m using it with T2


Sent from my iPhone using Tapatalk

24
EleksMaker IV Axis / Connecting 2 and 3 axes boards
« on: February 07, 2018, 01:31:55 AM »
Hi

Now I have a 2 axes and a 3 axes board , both EleksMaker

I was thinking of bridge the two together so I have at least a 4 axes to work with.

I am looking for a rotary setup so I can keep my z-axes

Is this any good?

https://www.banggood.com/CNC-Router-Rotational-Rotary-Axis-CNC-Machine-Accessory-Tailstock-for-4th-Axis-p-1154485.html?rmmds=cart_middle_products&cur_warehouse=CN

25
T2 Engraving / Re: Adjustable Z axis Module Motor
« on: February 05, 2018, 10:59:54 PM »
I have one installet on my A3 laser from banggood, works very well but is heavy, so when I don't use the laser I support the z axes so that it don't twist my x-axes, well I don't know if it will twist the x-axes, just to be sure  :)


26
T2 Engraving / Re: Item #35 in manual
« on: January 19, 2018, 08:50:49 AM »
Quote from: Zax on January 19, 2018, 04:06:20 AM
That is correct. Trace and Engrave Frame features are disabled for CNC mode.

It is deliberate and was done for safety reasons but would be very easy to change, perhaps I could allow trace frame (spindle off) at Z-safe as a compromise?

Hi Zax

I could be nice if we just could trace the frame with Z-safe settings, maybe with a warning.

thanks for good support



27
T2 Engraving / Re: Item #35 in manual
« on: January 19, 2018, 03:49:44 AM »
Hi

About tracing frame

I am trying to use T2 as a cnc milling tool, when I set the Z >0 then I can't trace the frame. I need to deselect cnc mode before I can trace the frame?


28
T2 Engraving / Re: Control servo with T2 laser using Mana Se without draw machine
« on: January 11, 2018, 02:38:47 AM »
Quote from: Topher on January 09, 2018, 07:51:55 AM
When I tried to plug a servo straight into the mana board I couldn't get it to do anything except buzz and lock up, no matter what s value I used. How does it work?

Start using small values for the servo


29
T2 Engraving / Re: Control servo with T2 laser using Mana Se without draw machine
« on: January 09, 2018, 12:19:29 AM »
Hi

I am using the serverport when draving (3D printed my ovn pen holder)

30
EleksMaker L7 / Re: Need help throubleshooting / maybe fixing the controller board
« on: January 05, 2018, 01:13:55 AM »
Well a new 3-axe board cost only 30 USD  :)

Pages: 1 [2] 3 4 5