Author Topic: laser stove :)  (Read 1545 times)

Hokuro

  • Jr. Member
  • **
  • Posts: 88
    • View Profile
laser stove :)
« on: February 04, 2019, 12:13:24 PM »
Hi guys,
I read a lot of threads and I became paranoid: my laser was resting on a chipboard and needed continuous surveillance.
Now I have created this "monster" and I can leave the laser to work alone.
In the worst case the garage is heated.
It's not very nice but I make it with scraps. I have a lot of scraps...
I hope you like it.
my english is very bad, please be patient. :)

ggallant571

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3243
    • View Profile
Re: laser stove :)
« Reply #1 on: February 04, 2019, 01:11:00 PM »
Did you mean to attach a picture?
SARCASM - Just one more service we offer here.

kibodwin

  • Hero Member
  • *****
  • Posts: 739
    • View Profile
Re: laser stove :)
« Reply #2 on: February 05, 2019, 02:14:14 AM »
Is this a special method of heating your tea with a laser... I am interested!!
=)
Laser: 2500mw A3 eleksmaker L5, K40 with Cohesion3D mini board, air assist, laser pointer etc..
OS: Windows 7, Debian, OpenSuse, Kali
Software: T2Laser, laserweb4, Repitier, Cura
Prusa i3 Clone GT2560
Anycubic Kossel Delta ramps

Hokuro

  • Jr. Member
  • **
  • Posts: 88
    • View Profile
Re: laser stove :)
« Reply #3 on: February 05, 2019, 02:49:11 AM »
Sorry, is one week that I have problems to access the forum from the desktop PC "the site is not responding" and I have to use an anonymous site that misses the formatting.
my english is very bad, please be patient. :)

ggallant571

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3243
    • View Profile
Re: laser stove :)
« Reply #4 on: February 05, 2019, 06:00:55 AM »
@kibodwin - You have it wrong!!. The laser is for etching your initials in the tea leaves.
SARCASM - Just one more service we offer here.

kibodwin

  • Hero Member
  • *****
  • Posts: 739
    • View Profile
Re: laser stove :)
« Reply #5 on: February 06, 2019, 03:12:52 AM »
typical, I always get the wrong end of the stick!!

cool container, I would advice some good extraction as the smoke will mess with the pc you have in the container...
How about adding a webcam to monitor the laser when in use?
=)
Laser: 2500mw A3 eleksmaker L5, K40 with Cohesion3D mini board, air assist, laser pointer etc..
OS: Windows 7, Debian, OpenSuse, Kali
Software: T2Laser, laserweb4, Repitier, Cura
Prusa i3 Clone GT2560
Anycubic Kossel Delta ramps

Hokuro

  • Jr. Member
  • **
  • Posts: 88
    • View Profile
Re: laser stove :)
« Reply #6 on: February 06, 2019, 04:28:54 AM »
work in progress.
extractor and webcam to be mounted, yesterday I received from China the powerlan to remote control, I'm waiting for ip-relais to remotely control the power of the laser.
the monitor is outside the box, it was inside only for the works
my english is very bad, please be patient. :)