« previous next »
Pages: [1]

Author Topic: laser stove :)  (Read 1836 times)

Hokuro

  • Jr. Member
  • **
  • Posts: 88
    • View Profile
laser stove :)
« on: February 04, 2019, 12:13:24 PM »
Hi guys,
I read a lot of threads and I became paranoid: my laser was resting on a chipboard and needed continuous surveillance.
Now I have created this "monster" and I can leave the laser to work alone.
In the worst case the garage is heated.
It's not very nice but I make it with scraps. I have a lot of scraps...
I hope you like it.
Logged
my english is very bad, please be patient. :)

ggallant571

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3263
    • View Profile
Re: laser stove :)
« Reply #1 on: February 04, 2019, 01:11:00 PM »
Did you mean to attach a picture?
Logged
SARCASM - Just one more service we offer here.

kibodwin

  • Hero Member
  • *****
  • Posts: 739
    • View Profile
Re: laser stove :)
« Reply #2 on: February 05, 2019, 02:14:14 AM »
Is this a special method of heating your tea with a laser... I am interested!!
=)
Logged
Laser: 2500mw A3 eleksmaker L5, K40 with Cohesion3D mini board, air assist, laser pointer etc..
OS: Windows 7, Debian, OpenSuse, Kali
Software: T2Laser, laserweb4, Repitier, Cura
Prusa i3 Clone GT2560
Anycubic Kossel Delta ramps

Hokuro

  • Jr. Member
  • **
  • Posts: 88
    • View Profile
Re: laser stove :)
« Reply #3 on: February 05, 2019, 02:49:11 AM »
Sorry, is one week that I have problems to access the forum from the desktop PC "the site is not responding" and I have to use an anonymous site that misses the formatting.
Logged
my english is very bad, please be patient. :)

ggallant571

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3263
    • View Profile
Re: laser stove :)
« Reply #4 on: February 05, 2019, 06:00:55 AM »
@kibodwin - You have it wrong!!. The laser is for etching your initials in the tea leaves.
Logged
SARCASM - Just one more service we offer here.

kibodwin

  • Hero Member
  • *****
  • Posts: 739
    • View Profile
Re: laser stove :)
« Reply #5 on: February 06, 2019, 03:12:52 AM »
typical, I always get the wrong end of the stick!!

cool container, I would advice some good extraction as the smoke will mess with the pc you have in the container...
How about adding a webcam to monitor the laser when in use?
=)
Logged
Laser: 2500mw A3 eleksmaker L5, K40 with Cohesion3D mini board, air assist, laser pointer etc..
OS: Windows 7, Debian, OpenSuse, Kali
Software: T2Laser, laserweb4, Repitier, Cura
Prusa i3 Clone GT2560
Anycubic Kossel Delta ramps

Hokuro

  • Jr. Member
  • **
  • Posts: 88
    • View Profile
Re: laser stove :)
« Reply #6 on: February 06, 2019, 04:28:54 AM »
work in progress.
extractor and webcam to be mounted, yesterday I received from China the powerlan to remote control, I'm waiting for ip-relais to remotely control the power of the laser.
the monitor is outside the box, it was inside only for the works
Logged
my english is very bad, please be patient. :)
Pages: [1]
« previous next »